Macheng Mine Excavator

  • Dangers and Load on Generators | Critical Power Supplies

    Apr 29, 2019 · It is mostly agreed that generators are to be run at a minimum load of 30% of maximum capacity. This is an absolute minimum and far from ideal – generally, a load of 60-75% of maximum capacity is considered preferable. No load operation, other than for short diagnostic runs such as checking for proper idle, should be avoided at all costs.

    Learn More
  • OSHA Requirements for Use of Taglines | Work - Chron.com

    Jul 08, 2020 · OSHA Requirements for Use of Taglines. When a crane lifts an object, it can swing into objects around it, into power lines or, by swinging, create hazards to personnel on the ground. Taglines, long ropes attached to the load, allow ground personnel …

    Learn More
  • BEST RIGGING PRACTICES IN LIFTING OPERATIONS, …

    Working Load limit (Rated Capacity) –the maximum static load permitted by the manufacturer. 2 for minimum stress on the sling. 4. Protect the load and sling from damage –Select the best sling used to handle long or wide load and serves to "spread" the load over more than one lifting point. Often used in conjunction with slings.

    Learn More
  • Rigging Fundamentals 101 (Rigging Hardware & Slings)

    KNOWN WORKING LOAD LIMITS? The working load limit is the maximum mass or force which the product is authorized to support in general service when the pull is applied in-line, unless noted otherwise, with respect to the centerline of the product. This term is used interchangeably with the following terms: WLL, rated load value, resultant working

    Learn More
  • Optimizing Loader Productivity | For Construction Pros

    Working Under a Suspended Load | OSHA Suspended Load

    Learn More
  • Dangers and Load on Generators | Critical Power Supplies

    Apr 29, 2019 · It is mostly agreed that generators are to be run at a minimum load of 30% of maximum capacity. This is an absolute minimum and far from ideal – generally, a load of 60-75% of maximum capacity is considered preferable. No load operation, other than for short diagnostic runs such as checking for proper idle, should be avoided at all costs.

    Learn More
  • Working Under a Suspended Load | OSHA Suspended Load

    Jun 19, 2018 · Be careful that the load does not shift outside of the equipment's tires or tracks. The equipment may tip over. Check that all alarms and horns are in working order. Maintain a distance of 10 feet from power lines. Safety by Design Is Here to Help. When working under a suspended load OSHA requires certain standards to be met.

    Learn More
  • Backhoe/Loader/ Operator Safety Training

    Front End Loader Operator - Workplace Safety North

    Learn More
  • Forest Operations Equipment Catalog: Cable Logging

    There are a number of safety issues when working around cable operations. Anchor failure can be mitigated using solid anchors and proper anchor building techniques. Cable failures can result from inadequate deflection, poorly maintained cables, trying to haul loads larger than the safe working load of the cables, and numerous other factors.

    Learn More
  • 1926 Subpart L App A - Scaffold Specifications

    Scaffolds. Standard Number: 1926 Subpart L App A. Title: Scaffold Specifications. GPO Source: e-CFR. This Appendix provides non-mandatory guidelines to assist employers in complying with the requirements of subpart L of this part. An employer may use these guidelines and tables as a starting point for designing scaffold systems.

    Learn More
  • SPECIFICATIONS & REQUIREMENTS FOR - PSEG Long Island

    PSEG Long Island Redbook TD-DD-RED OPERATIONS MANUAL DOCUMENT HIERARCHY Page 3 of 114 OPERATIONS MANUAL DOCUMENT HIERARCHY The PSEG Long Island Operations Manual is composed of five levels of documents: • Core Functions. Core Functions define the functional areas of the Operations Manual that are critical to the operation of the Utility.

    Learn More
  • 3c. Loading and Hauling Operations

    Operations Construction Methods 110401542 Loaders –Traveling a minimum distance Estimating Loader Production • Typical values for basic cycle time 3c - ٦ hauling, and dumping material over medium to long haul distances • The scraper excavates by lowering the front edge

    Learn More
  • Corral and Working Facilities for Beef Cattle | Oklahoma

    Corral and Working Facilities for Beef Cattle. The primary reasons for constructing a corral and working facility are to observe cattle closely, perform routine health functions, and improve labor efficiency. A good working facility is merely an extension of a well-planned corral …

    Learn More
  • Lifting operations and lifting equipment - OSHWiki

    Lifting operations. A lifting operation is an operation concerned with the lifting and lowering of a load. A load is the item or items being lifted which could include a person or people. A lifting operation may be performed manually or using lifting equipment. Manual lifting, holding, putting down, carrying or moving is often referred to as

    Learn More
  • training.gov.au - TLILIC0002 - Licence to operate a

    Weather and work environment conditions are assessed to determine any impact on vehicle loading crane operations in accordance with manufacturer requirements and safe work procedures. 3 . Perform work/task . 3.1 . Lifts are determined within the RC of the vehicle loading crane in accordance with the load chart/s and lift plan. 3.2

    Learn More
  • 1926.305 - Jacks-lever and ratchet, screw, and hydraulic

    "Operation and maintenance." 1926.305(d)(1)(i) After the load has been raised, it shall be cribbed, blocked, or otherwise secured at once. 1926.305(d)(1)(ii) Hydraulic jacks exposed to freezing temperatures shall be supplied with an adequate antifreeze liquid. For jacks sent out of shop for special work, when sent out and when returned

    Learn More
  • Using the Load Distance Technique for Site Planning

    First, the loads times distance for supplier 1 is 22.36 times 200, or 4,472. The loads times distance for supplier 2 is 3,640. Add the two together, and you get 8,072 as the load distance score

    Learn More
  • When don't I need a licence? | WorkSafe.qld.gov.au

    the work is carried out at the workplace solely for the manufacture, testing, trialing, installation, commissioning, maintenance, servicing, repair, alteration, demolition or disposal of the plant or moving the plant within the workplace and the plant is operated or used without a load except when standard weight loads with predetermined fixing

    Learn More
  • TEST Wheel Loader Operation Techniques Kefid

    Aug 01, 2004 · Don't allow the loader to idle for more than 10 minutes. Unnecessary idling wastes fuel. Allow the machine to do the shifting. Auto-shift transmissions determine the best gear for specific loads

    Learn More
  • 1926.305 - Jacks-lever and ratchet, screw, and hydraulic

    "Operation and maintenance." 1926.305(d)(1)(i) After the load has been raised, it shall be cribbed, blocked, or otherwise secured at once. 1926.305(d)(1)(ii) Hydraulic jacks exposed to freezing temperatures shall be supplied with an adequate antifreeze liquid. For jacks sent out of shop for special work, when sent out and when returned

    Learn More